P38 cigarette lighter socket

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
WayneRR4x4

WayneRR4x4

Active Member
Posts
120
Location
Brecon
Ok guys, I have the P38 battery gremlin.... yup, I wake up to a flat battery if I leave the Tank standing for a couple of days.
I've disconnected the RF unit aerial, which helps, and I've ordered a power cut-out unit to put in the power feed for the RF unit... yeah, I'll be the guy with two fobs lol... but I want to use a solar panel to trickle charge the battery.
I found a great one on t'interwebby, bought it, popped the lead in and........ it doesn't work.
Turns out my cigarette socket isn't permanently live, which means when I switch the ignition off it wont allow the solar panel to work.
So, (and congrats for sticking with this, soz to go on lol) how do I make the socket permanently live?
Please, keep it simple, use small words and colours, and please start with how the hell do I remove the trim the socket sits in without breaking it?
 
Wire it straight to the battery? Surely that will keep it always live? As to the trim not a clue I don't have a p38 but probably a screwdriver and hammer :)
 
just run a wire from the battery into the cabin with a fuse and socket or cigarette lighter socket on it and plug the panel into that.
 
mattmaclaren said:
Wire it straight to the battery? Surely that will keep it always live? As to the trim not a clue I don't have a p38 but probably a screwdriver and hammer :)
Click to expand...

Ok... I may not be a whizz with wiring, but even I know you shouldn't just wire it direct to the battery lol
 
A lot of solar panels have croc clips to go straight on to battery so will be ok wired direct.
the rf cut out should be wired in so it cuts the orange wire which is feed from receiver to becm and take the power supply to run it from the red and black.
 
tarphenry said:
just run a wire from the battery into the cabin with a fuse and socket or cigarette lighter socket on it and plug the panel into that.
Click to expand...

Now, that's more like it... except I have questions.
How do I get the wire into the cabin from the engine compartment?
I'm guessing I need a live and earth connection?
What rate fuse do I use?
 
When you buy the remote switch make sure it doesnt operate at 433Mhz or it wont work.Fuse same size as panel max 5 amp. you will need to follow wiring loom to find acess
 
You can stick a couple of wires through the seal for the heater pipes and get at them inside the cabin with the panel above drivers feet removed.
 
Easiest way is to wire a socket into the 12V permanent live for the towing electrics on the left hand (passenger side) side of the vehicle behind the rear light cluster. I did that for just this purpose and so I had a power supply in the boot.
 
Grrrrrr said:
Easiest way is to wire a socket into the 12V permanent live for the towing electrics on the left hand (passenger side) side of the vehicle behind the rear light cluster. I did that for just this purpose and so I had a power supply in the boot.
Click to expand...

That's a good idea, hadn't thought of that. I can charge my boost pack then so its always ready.
 
You must log in or register to reply here.

Similar threads

A
Super Locked
2
Replies
22
Views
1K
Kyle1912
K
P38 guy
P38A Aftermarket remote
Replies
1
Views
445
pwood999
pwood999
I
P38 BeCM locked?
Replies
8
Views
761
pwood999
pwood999
B
P38A Cigarette Lighter Socket Removal
Replies
5
Views
2K
Datatek
Datatek
F
2001 P38 2.5 Diesel EKA Via NANOCOM
2
Replies
35
Views
2K
Datatek
Datatek
Back
Top